 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| data sheet 1 rev. 1.0 www.infineon.com/automotive-transceiver 2017-08-09 TLE9250X high speed can transceiver 1 overview qualified for automotive applic ations according to aec-q100 features ? fully compliant to iso 11898-2 (2016) and sae j2284-4/-5 ? reference device and part of intero perability test specification for can transceiver ? guaranteed loop delay symmetry for can fd data frames up to 5 mbit/s ? very low electromagnetic emission (eme) allows the use without additional common mode choke ? v io input for voltage adaption to the c interface (3.3v & 5v) ? wide common mode range for el ectromagnetic immunity (emi) ? excellent esd robustness +/-8kv (hbm) and +/-11kv (iec 61000-4-2) ? extended supply range on the v cc and v io supply ? can short circuit proof to ground, battery, v cc and v io ? txd time-out function ? very low can bus leakage current in power-down state ? overtemperature protection ? protected against automotive transients according iso 7637 and sae j2962-2 standards ?receive-only mode ? green product (rohs compliant) ? small, leadless tson8 package designed for automated optica l inspection (aoi) ? aec qualified potential applications ? engine control unit (ecus) ? electric power steering ? transmission control units (tcus) ? chassis control modules pg-tson-8 pg-dso-8
data sheet 2 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver overview description the TLE9250X is the latest infineon high-speed can transceiver generation , used inside hs can networks for automotive and also for industrial a pplications. it is designed to fulf ill the requirements of iso 11898-2 (2016) physical layer specification and respecti vely also the sae standards j1939 and j2284. the TLE9250X is available in a pg-dso -8 package and in a small, leadless pg-tson-8 package. both packages are rohs compliant and halogen fr ee. additionally the pg-tson-8 pa ckage supports the solder joint requirements for automated optical inspection (aoi). as an interface between the physical bus layer and th e hs can protocol controller , the TLE9250X protects the microcontroller against interferences generated inside the network. a very high esd robustness and the perfect rf immunity allows the use in automotive application without addi ng additional protection devices, like suppressor diodes for example. while the transceiver TLE9250X is not su pplied the bus is switched off and illustrate an ideal passive behavior with the lowest possible load to all other subscribers of the hs can network. based on the high symmetry of the ca nh and canl output signals, the tl e9250x provides a very low level of electromagnetic emission (e me) within a wide frequenc y range. the TLE9250X fulfi lls even stringent emc test limits without additional ex ternal circuit, like a common mode choke for example. the perfect transmitter symmetry comb ined with the optimized delay symm etry of the receiver enables the TLE9250X to support can fd data frames. depending on the size of the network and the along coming parasitic effects the device su pports bit rates up to 5 mbit/s. fail-safe features like overtemperat ure protection, output current limita tion or the txd time-out feature protect the TLE9250X and the external circuitry from ir reparable damage. type package marking TLE9250Xle pg-tson-8 9250x TLE9250Xsj pg-dso-8 9250x data sheet 3 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver 1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.2 pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 high-speed can functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.1 high-speed can physical layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 normal-operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.2 forced-receive-only mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.3 receive-only mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.4 power-down state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 changing the mode of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6.1 power-up and power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6.2 mode change by the rm pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6.3 mode changes by v cc undervoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7 fail safe functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.1 short circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.2 unconnected logic pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.3 txd time-out function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.4 overtemperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8 general product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8.2 functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8.3 thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 9.1 functional device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 9.2 diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 10 application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 10.1 esd robustness according to iec61000-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 10.2 application example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 10.3 voltage adaption to the microcontroller supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 10.4 further application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 11 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 12 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table of contents data sheet 4 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver block diagram 2 block diagram figure 1 functional block diagram driver temp- protection mode control 7 canh 6 canl 2 gnd txd 3 v cc rm v io rxd timeout transmitter receiver v cc /2 normal-mode receiver 5 1 8 4 bus-biasing = data sheet 5 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver pin configuration 3 pin configuration 3.1 pin assignment figure 2 pin configuration 3.2 pin definitions table 1 pin defini tions and functions pin no. symbol function 1txd transmit data input; internal pull-up to v io , ?low? for ?dominant? state. 2gnd ground 3 v cc transmitter supply voltage; 100 nf decoupling capaci tor to gnd required. 4rxd receive data output; ?low? in ?dominant? state. 5 v io digital supply voltage; supply voltage input to adapt the logica l input and output voltage levels of the transceiver to the mi crocontroller supply, 100 nf decoupling capaci tor to gnd required. 6canl can bus low level i/o; ?low? in ?dominant? state. 7canh can bus high level i/o; ?high? in ?dominant? state. 8rm receive-only input; internal pull-down to gnd, ?l ow? for normal-operating mode. pad ? connect to pcb heat sink area. do not connect to other potential than gnd. txd rm v io 1 2 3 4 8 7 6 5 gnd v cc rxd canh canl 1 2 3 4 8 7 6 5 txd gnd v cc rxd rm v io canh canl (top-side x-ray view) pad data sheet 6 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver high-speed can functional description 4 high-speed can functional description hs can is a serial bus system that connects microcon trollers, sensors and actuators for real-time control applications. the use of the controller area network (abbreviated can) within road vehicles is described by the international standard iso 11898. according to the 7-layer osi reference model the physical layer of a hs can bus system specifies the data transmission from one can node to all other available can nodes within the network. the physical layer specification of a can bus system includes all electrical specifications of a can network. the can transceiver is part of the physical layer specificatio n. several different physical layer standards of can networks have b een developed in recent years. the TLE9250X is a high-speed can transceiver with a dedicated bus wa ke-up function as defined in th e latest iso 11898-2 hs can standard. 4.1 high-speed can physical layer figure 3 high-speed can bu s signals and logic signals txd v io t t v cc canh canl t v cc v diff rxd v io t v io = digital supply voltage v cc = transmitter supply voltage txd = transmit data input from the microcontroller rxd = receive data output to the microcontroller canh = bus level on the canh input/output canl = bus level on the canl input/output v diff = differential voltage between canh and canl v diff = v canh C v canl dominant receiver threshold recessive receiver threshold t loop(h,l) t loop(l,h) data sheet 7 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver high-speed can functional description the TLE9250X is a high-speed can tran sceiver, operating as an interfac e between the can controller and the physical bus medium. a hs can network is a two wire, differential network which allows data transmission rates up to 5 mbit/s. the characteristic for a hs ca n network are the two signal states on the can bus: ?dominant? and ?recessive? (see figure 3 ). the canh and canl pins are the interface to the can bu s and both pins operate as an input and output. the rxd and txd pins are the interface to the microcontroller. the pin txd is the serial data input from the can controller, the rxd pin is the serial data output to the can cont roller. as shown in figure 1 , the hs can transceiver TLE9250X includes a receiver and a transmitter unit, allowing th e transceiver to send data to the bus medium and monitor the data from the bus medi um at the same time. the hs can transceiver TLE9250X converts the serial data stream which is available on the transmit data input txd, into a differential output signal on the can bus, provided by the canh and canl pins. the receiver stage of the TLE9250X monitors the data on the can bus and conv erts them to a serial, single-ended signal on the rxd output pin. a logical ?low? signal on the txd pin creates a ?dominant? signal on th e can bus, followed by a logical ?low? signal on the rxd pin (see figure 3 ). the feature, broadcasting da ta to the can bus and listenin g to the data traffic on the can bus simultaneously is essential to support the bit-to-bit arbitration within can networks. the voltage levels for hs can transc eivers are defined in iso 11898-2. whether a data bit is ?dominant? or ?recessive? depends on the voltage differ ence between the canh and canl pins: v diff = v canh - v canl . to transmit a ?dominant? signal to the can b us the amplitude of the differential signal v diff is higher than or equal to 1.5 v. to receive a ?rec essive? signal from the can bus the amplitude of the differential v diff is lower than or equal to 0.5 v. ?partially-supplied? high-speed can networks are th ose where the can bus nodes of one common network have different power supply conditions. some nodes are connected to the common power supply, while other nodes are disconnected from the powe r supply and in power-down state. regardless of whether the can bus subscriber is supplied or not, each subscriber co nnected to the common bus media must not interfere with the communication. the TLE9250X is designed to support ?partially-s upplied? networks. in power-down state, the receiver input resistors are switched of f and the transceiver input has a high resistance. . the voltage level on the digital input txd and the digita l output rxd is determined by the power supply level at the v io pin. depending on the voltage level at the v io pin, the signal levels on the logic pins (stb, txd and rxd) are compatible with microcontrollers having a 5 v or 3.3 v i/o supply. usually the digital power supply v io of the transceiver is connected to the i/ o power supply of the microcontroller (see figure 15 ). data sheet 8 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver modes of operation 5 modes of operation the TLE9250X supports three diff erent modes of operation (see figure 4 and table 2 ): ? normal-operating mode ?receive-only mode ?forced-receive-only mode mode changes are either triggered by the mode selectio n input pin rm or by an undervoltage event on the transmitter supply v cc . an undervoltage event on the digital supply v io powers down the TLE9250X. figure 4 mode state diagram table 2 modes of operation mode rm v io v cc bus bias transmitter normal-mode receiver normal-operating ?low? ?on? ?on? v cc /2 ?on? ?on? receive-only ?high? ?on? ?on? v cc /2 ?off? ?off? forced-receive-only ?x? ?on? ?x? gnd ?off? ?on? power-down state ?x? ?off? ?x? floating ?off? ?off? rm v cc v io power-down state x x off normal-operating mode rm v cc v io 0 on on forced- receive-only mode rm v cc v io x off on receive-only mode rm v cc v io 1 on on v io on v cc off rm x v io on v cc on rm 0 v io on v cc on rm 1 v io on v cc off rm x v io on v cc on rm 1 v io on v cc on rm 0 v io on v cc on rm 0 v io on v cc on rm 1 v io on v cc off rm x data sheet 9 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver modes of operation 5.1 normal-operating mode in normal-operating mode the transceiver TLE9250X sends and receives data from the hs can bus. all functions are active (see also figure 4 and table 2 ): ? the transmitter is active and drives the serial data stream on the txd input pin to the bus pins canh and canl. ? the normal-mode receiver is active and converts the signals from the bus to a serial data stream on the rxd output. ? the rxd output pin indicates the data received by the normal-mode receiver. ? the bus biasing is connected to v cc /2. ? the rm input pin is active and changes the mode of operation. ? the txd time-out function is enabled and disconnect s the transmitter in case a time-out is detected. ? the overtemperature protection is enabled and discon nects the transmitter in ca se an overtemperature is detected. ? the undervoltage detection on v cc is enabled and triggers a mode ch ange to forced-receive-only in case an undervoltage event is detected. ? the undervoltage detection on v io is enabled and powers down the device in case of detection. normal-operating mode is entered from and forced -receive-only mode, when the rm input pin is set to logical ?low?. normal-operating mode can only be en tered when all supplies are available: ? the transmitter supply v cc is available ( v cc > v cc(uv,r) ). ? the digital supply v io is available ( v io > v io(uv,r) ). 5.2 forced-receive-only mode the forced-receive-only mode is a fa il-safe mode of the TLE9250X, which wi ll be entered when the transmitter supply v cc is not available . the following functions are available (see also figure 4 and table 2 ): ? the transmitter is disabled and the data available on the txd input is blocked. ?the normal-mode re ceiver is enabled. ? the rxd output pin indicates the data received by the normal-mode receiver. ? the bus biasing is connected to gnd. ? a mode change by setting the rm input pin logical to ?high? or ?low? does not change the mode of operation. ? the txd time-out function is disabled. ? the overtemperature protection is disabled. ? the undervoltage detection on v cc is active. ? the undervoltage detection on v io is enabled and powers down the device in case of detection. ? forced-receive-only mode is entered from power-down state if the input pin is set to logical ?low? and the digital supply v io is available ( v io > v io(uv,r) ). ? forced-receive-only mode is ente red from normal-operating mode by an undervoltage event on the transmitter supply v cc . 5.3 receive-only mode in receive-only mode the transmitte r is disabled and the receiver is enabled. the TLE9250X can receive data from the bus, but cannot send any message (see also figure 4 and table 2 ): data sheet 10 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver modes of operation ? the transmitter is disabled and the data available on the txd input is blocked. ?the normal-mode re ceiver is enabled. ? the rxd output pin indicates the data received by the normal-mode receiver. ? the bus biasing is connected to v cc /2. ? the rm input pin is active and changes the mode of operation to normal-operating mode, if logical ?low?. ? the txd time-out function is disabled. ? the overtemperature protection is disabled. ? the undervoltage detection on v cc is active and changes the mode of operation to forced-receive-only mode in case of detection. ? the undervoltage detection on v io is enabled and powers down the device in case of detection. ? receive-only mode can only be entered when v cc ( v cc > v cc(uv,r) ) and v io ( v io > v io(uv,r) ) are available. 5.4 power-down state independent of the transmitter supply v cc and rm input pin the TLE9250X is powered down if the supply voltage v io < v io(uv,r) (see figure 4 ). in the power-down state the differential input resistor s of the receiver are switch ed off. the canh and canl bus interface of the TLE9250X is floati ng and acts as a high-impedance inpu t with a very small leakage current. the high-ohmic input does not influe nce the ?recessive? level of the ca n network and allows an optimized eme performance of the entire hs can network. in power-down state the tr ansceiver is an invisible node to the bus. data sheet 11 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver changing the mode of operation 6 changing the mode of operation 6.1 power-up and power-down the hs can transceiver TLE9250X powers up by applying the digital supply v io to the device ( v io > v io(u,r) ). . after powering up, the device enters one out of three operating modes (see figure 5 and figure 6 ). depending on the condition of the transmitter supply voltage v cc and the mode selection pin rm the device can enter every mode of operation after the power-up: ? v cc is available and the rm input is set to ?low? - norm al-operating mode ? v cc is disabled - forced-receive-only mode ? v cc is available and the rm input is set to ?high? - receive-only mode the device TLE9250X powers down when the v io supply falls below the undervoltage detection threshold ( v io < v io(u,f) ), regardless if the transmitter supply v cc is available or not. the powe r-down detection is active in every mode of operation. figure 5 power-up and power-down figure 6 power-up an d power-down timings rm v cc v io power-down state x x off normal-operating mode rm v cc v io 0 on on forced- receive-only mode rm v cc v io x off on receive-only mode rm 1 on on v io on v cc off rm 0 v io on v cc on rm 0 v io on v cc on rm 1 v io off v io off v io off v io off blue -> indicates the event triggering the power-up or power-down red -> indicates the condition which is required to reach a certain operating mode v cc v io t rm x = dont care low due the internal pull-down resistor 1) t pon v io hysteresis v io(uv,h) t v io undervoltage monitor v io(uv,f) v io undervoltage monitor v io(uv,r) transmitter supply voltage v cc available power-down state any mode of operation normal-operating mode t poff 1) assuming no external signal applied "0" for normal-operating mode "1" for receive-only mode data sheet 12 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver changing the mode of operation 6.2 mode change by the rm pin when the TLE9250X is supplied with the digital voltage v io the internal logic works and mode change by the mode selection pin rm is possible. by default the rm input pin is logica l ?low? due to the internal pull-down current source to gnd. changing the rm input pin to logical ?high? in normal-operating mo de triggers a mode change to receive-only mode (see figure 7 ). to enter normal-operating mode or re ceive-only mode the transmitter supply v cc needs to be available. figure 7 mode selection by the rm pin rm v cc v io power-down state x x off normal-operating mode rm v cc v io 0 on on forced- receive-only mode rm v cc v io x off on receive-only mode rm v cc v io 1 on on rm 1 rm 0 data sheet 13 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver changing the mode of operation 6.3 mode changes by v cc undervoltage when the transmitter supply v cc ( v cc < v cc(u/f) ) is in undervoltage condition, the TLE9250X might not be able to provide the correct bus levels on the canh and canl output pins. to avoi d any interference with the network the TLE9250X blocks the tr ansmitter and changes the mode of oper ation when an undervoltage event is detected (see figure 8 and figure 9 ). in normal-operating mode and in receive-only mode a undervoltage event on supply v cc ( v cc < v cc(u/f) ) triggers a mode change to forced-receive-only mode. in forced-receive-only mode the undervoltage detection v cc ( v cc < v cc(u/f) ) is enabled. in this mode the TLE9250X can operate without the transmitter supply v cc . due to the internal pull-down current source at rm input pin the tr ansceiver changes the mode of operation from forced-receive-only mode to normal-operating mode if v cc is supplied again and no external signal is applied to the rm input pin. figure 8 mode changes by undervoltage events on v cc rm v cc v io power-down state x x off normal-operating mode rm v cc v io 0 on on forced- receive-only mode rm v cc v io x off on receive-only mode rm v cc v io 1 on on v io on v cc off rm 0 v io on v cc on rm 0 v io on v cc off rm 1 data sheet 14 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver changing the mode of operation figure 9 undervoltage on the transmitter supply v cc forced-receive only mode any mode of operation normal-operating mode t rm x = dont care low due the internal pull-down resistor 1) 1) assuming no external signal applied digital supply voltage v io = on t delay(uv) v cc hysteresis v cc(uv,h) t v cc undervoltage monitor v cc(uv,f) v cc undervoltage monitor v cc(uv,r) t delay(uv) data sheet 15 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver fail safe functions 7 fail safe functions 7.1 short circuit protection the canh and canl bus pins are prov en to cope with a short circuit fa ult against gnd and against the supply voltages. a current limiting circuit pr otects the transceiver against damages. if the device is heating up due to a continuous short on the canh or canl, the internal ov ertemperature protection switches off the bus transmitter. 7.2 unconnected logic pins the rm input pin has an internal pull -down current source to gnd. all other logic input pins have an internal pull-up current source to v io . in case the v io and v cc supply is activated and the logical pins are open, the TLE9250X enters into the normal -operating mode by default. 7.3 txd time-out function the txd time-out feature protects th e can bus against permanent blocking in case the logical signal on the txd pin is continuously ?low?. a continuous ?low? signal on the txd pin might have its root cause in a locked- up microcontroller or in a short circuit on the printed circuit board, for example. in normal-operating mode, a logical ?low? signal on the txd pin for the time t > t txd enables the txd time-out feature and the TLE9250X disa bles the transmitter (see figure 10 ). the receiver is still active and the data on the bus continues to be monitored by the rxd output pin. figure 10 txd time-out function figure 10 illustrates how the transmitter is deactivated and activa ted again. a permanent ?low? signal on the txd input pin activates the txd time-out function and de activates the transmitter. to release the transmitter after a txd time-out event, the TLE9250X requires a sign al change on the txd input pin from logical ?low? to logical ?high?. txd t t canh canl rxd t txd time-out txd timeCout released t > t txd data sheet 16 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver fail safe functions 7.4 overtemperature protection the TLE9250X has an integrated ov ertemperature detection to prot ect the TLE9250X against thermal overstress of the transmitter. the overtemperature prot ection is only active in normal-operating mode. in case of an overtemperature condition, the temper ature sensor will disable the transmitter while the transceiver remains in normal-operati ng mode. after the device has cooled down the transmitter is activated again (see figure 11 ). a hysteresis is implemented within the temperature sensor. figure 11 overtemperature protection txd t t canh canl rxd t t j t t jsd (shut down temperature) switch-on transmitter a t cool down data sheet 17 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver general product characteristics 8 general product characteristics 8.1 absolute maximum ratings note: stresses above the ones listed here may ca use permanent damage to the device. exposure to absolute maximum rating conditions for extended pe riods may affect device reliability. integrated protection functions are designed to prevent ic destruction under fa ult conditions described in the data sheet. fault conditions are considered as ?outside? normal -operating rang e. protection functions are not designed for continuos repetitive operation. table 3 absolute maximum ratings voltages, currents and temperatures 1) all voltages with respect to ground ; positive current flowing into pin; (unless otherwise specified) 1) not subject to production test, specified by design parameter symbol values unit note or test condition number min. typ. max. voltages transmitter supply voltage v cc -0.3 ? 6.0 v ? p_8.1.1 digital supply voltage v io -0.3 ? 6.0 v ? p_8.1.2 canh and canl dc voltage versus gnd v canh -40 ? 40 v ? p_8.1.3 differential voltage between canh and canl v can_diff -40 ? 40 v ? p_8.1.4 voltages at the digital i/o pins: rm, rxd, txd v max_io1 -0.3 ? 6.0 v ? p_8.1.5 voltages at the digital i/o pins: rm, rxd, txd v max_io2 -0.3 ? v io +0.3 v ? p_8.1.6 currents rxd output current i rxd -5 ? 5 ma ? p_8.1.7 temperatures junction temperature t j -40 ? 150 c ? p_8.1.8 storage temperature t s -55 ? 150 c ? p_8.1.9 esd resistivity esd immunity at canh, canl versus gnd v esd_hbm_can -8 ? 8 kv hbm (100 pf via 1.5 k ? ) 2) 2) esd susceptibility, human body model ?hbm? according to ansi/esda/jedec js-001 p_8.1.11 esd immunity at all other pins v esd_hbm_all -2 ? 2 kv hbm (100 pf via 1.5 k ? ) 2) p_8.1.12 esd immunity all pins v esd_cdm -750 ? 750 v cdm 3) 3) esd susceptibility, charge device model ?cdm ? according to eia/jesd22-c101 or esda stm5.3.1 p_8.1.13 data sheet 18 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver general product characteristics 8.2 functional range note: within the functional range the ic operates as described in the circuit de scription. the electrical characteristics are specified within the conditions given in the related electrical characteristics table. 8.3 thermal resistance note: this thermal data was generated in accord ance with jedec jesd51 standards. for more information, please visit www.jedec.org . table 4 functional range parameter symbol values unit note or test condition number min. typ. max. supply voltages transmitter supply voltage v cc 4.5 ? 5.5 v ? p_8.2.1 digital supply voltage v io 3.0 ? 5.5 v ? p_8.2.2 thermal parameters junction temperature t j -40 ? 150 c 1) 1) not subject to production test, specified by design. p_8.2.3 table 5 thermal resistance 1) 1) not subject to production test, specified by design parameter symbol values unit note or test condition number min. typ. max. thermal resistances junction to ambient pg-tson-8 r thja_tson8 ?65 ?k/w 2) 2) specified r thja value is according to jedec jesd51-2,-7 at natu ral convection on fr4 2s2p board. the product (TLE9250X) was simulated on a 76.2 x 114.3 x 1.5 mm boar d with 2 inner copper layers (2 x 70m cu, 2 x 35m cu) p_8.3.1 junction to ambient pg-dso-8 r thja_dso8 ? 120 ? k/w 2) p_8.3.2 thermal shutdown (j unction temperature) thermal shutdown temperature, rising t jsd 170 180 190 c temperature falling: min. 150c p_8.3.3 thermal shutdown hysteresis ? t 51020k p_8.3.4 data sheet 19 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver electrical characteristics 9 electrical characteristics 9.1 functional device characteristics table 6 electrical characteristics 4.5 v < v cc <5.5v; 3.0v< v io <5.5v; r l =60 ? ; -40 c < t j < 150 c; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. parameter symbol values unit note or test condition number min. typ. max. current consumption current consumption at v cc normal-operating, ?recessive? state i cc_r ?24ma v txd = v io , v rm =0v; p_9.1.1 current consumption at v cc normal-operating mode, ?dominant? state i cc_d ? 3860ma v txd = v rm =0v; p_9.1.2 current consumption at v io normal-operating mode i io ??1.5ma v rm =0v; v diff = 0v; v txd = v io ; p_9.1.3 current consumption at v cc receive-only mode i cc(rom) 1ma v rm = v io v cc,uv < v cc <5.5v; p_9.1.8 current consumption at v io receive-only mode i io(rom) 0.8 1.5 ma v rm = v io v cc,uv < v cc <5.5v; p_9.1.9 current consumption at v cc forced-receive-only mode i cc(from) ??1ma v txd = v rm = 0v; 0v< v cc < v cc(uv,f) ; v diff = 0v; p_9.1.10 current consumption at v io forced-receive-only mode i io(from) ?0.81.5ma v txd = v rm = 0 v; 0v< v cc < v cc(uv,f) ; v diff = 0v; p_9.1.11 supply resets v cc undervoltage monitor rising edge v cc(uv,r) 3.8 4.35 4.5 v ? p_9.1.12 v cc undervoltage monitor falling edge v cc(uv,f) 3.8 4.25 4.5 v ? p_9.1.13 v cc undervoltage monitor hysteresis v cc(uv,h) ? 100 ? mv 1) p_9.1.14 v io undervoltage monitor rising edge v io(uv,r) 2.0 2.55 3.0 v ? p_9.1.15 v io undervoltage monitor falling edge v io(uv,f) 2.0 2.4 3.0 v ? p_9.1.16 v io undervoltage monitor hysteresis v io(uv,h) ? 150 ? mv 1) p_9.1.17 v cc undervoltage delay time t delay(uv) ? ? 100 s 1) (see figure 9 ); p_9.1.18 v io delay time power-up t pon ? ? 280 s 1) (see figure 6 ); p_9.1.19 data sheet 20 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver electrical characteristics v io delay time power-down t poff ? ? 100 s 1) (see figure 6 ); p_9.1.20 receiver output rxd ?high? level output current i rxd,h ?-4-1 ma v rxd = v io -0,4v; v diff < 0,5v p_9.1.21 ?low? level output current i rxd,l 1 4 ? ma v rxd =0.4v; v diff > 0,9v p_9.1.22 transmission input txd ?high? level input voltage threshold v txd,h ?0.5 v io 0.7 v io v?recessive? state; p_9.1.26 ?low? level input voltage threshold v txd,l 0.3 v io 0.4 v io ?v?dominant? state; p_9.1.27 input hysteresis v hys(txd) ? 200 ? mv 1) p_9.1.28 ?high? level input current i txd,h -2 ? 2 a v txd = v io ; p_9.1.29 ?low? level input current i txd,l -200 ? -20 a v txd =0v; p_9.1.30 input capacitance c txd ??10pf 1) p_9.1.31 txd permanent ?dominant? time-out, optional t txd 1?4msnormal-operating mode; p_9.1.32 receive-only input rm ?high? level input voltage threshold v rm,h ?0.5 v io 0.7 v io v receive-only mode; p_9.1.36 ?low? level input voltage threshold v rm,l 0.3 v io 0.4 v io ? v normal-operating mode; p_9.1.37 ?high? level input current i rm,h 20 ? 250 a v rm = v io p_9.1.40 ?low? level input current i rm,l -2 ? 2 a v rm =0v p_9.1.41 input hysteresis v hys(rm) ? 200 ? mv 1) p_9.1.42 input capacitance c (rm) ??10pf 1) p_9.1.43 table 6 electrical characteristics (cont?d) 4.5 v < v cc <5.5v; 3.0v< v io <5.5v; r l =60 ? ; -40 c < t j < 150 c; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. parameter symbol values unit note or test condition number min. typ. max. data sheet 21 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver electrical characteristics bus receiver differential range ?dominant? normal-operating mode v diff_d_range 0.9 ? 8.0 v -12v v cmr 12 v; p_9.1.46 differential range ?recessive? normal-operating mode v diff_r_range -3.0 ? 0.5 v -12v v cmr 12 v; p_9.1.48 differential receiver hysteresis normal-operating mode v diff,hys 30 mv 1) p_9.1.49 common mode range cmr -12 ? 12 v ? p_9.1.52 single ended internal resistance r can_h , r can_l 6?50k ? ?recessive? state?, -2v v canh 7v; -2v v canl 7v; p_9.1.53 differential internal resistance r diff 12 ? 100 k ? ?recessive? state?, -2v v canh 7v; -2v v canl 7v; p_9.1.54 input resistance deviation between canh and canl ? r i -3 ? 3 % 1) ?recessive? state?, v canh = v canl = 5v; p_9.1.55 input capacitance canh, canl versus gnd c in ? 2040pf 1) p_9.1.56 differential input capacitance c indiff ? 1020pf 1) p_9.1.57 bus transmitter canl, canh ?recessive? output voltage normal-operating mode v canl,h 2.0 2.5 3.0 v v txd = v io, no load; p_9.1.58 canh, canl ?recessive? output voltage difference normal-operating mode v diff_r_nm = v canh - v canl -500 ? 50 mv v txd = v io , no load; p_9.1.59 canl ?dominant? output voltage normal-operating mode v canl 0.5 ? 2.25 v v txd =0v; 50 ? < r l <65 ? , 4.75 v < v cc <5.25v; p_9.1.60 canh ?dominant? output voltage normal-operating mode v canh 2.75 ? 4.5 v v txd =0v; 50 ? < r l <65 ? , 4.75 v < v cc <5.25v; p_9.1.61 differential voltage ?dominant? normal-operating mode v diff = v canh - v canl v diff_d_nm 1.5 2.0 3.0 v v txd =0v, 50 ? < r l <65 ? , 4.75 v < v cc <5.25v; p_9.1.62 differential voltage ?dominant? extended bus load normal-operating mode v diff_ext_bl 1.4 2.0 3.3 v v txd =0v, 45 ? < r l <70 ? , 4.75 v < v cc <5.25v; p_9.1.63 table 6 electrical characteristics (cont?d) 4.5 v < v cc <5.5v; 3.0v< v io <5.5v; r l =60 ? ; -40 c < t j < 150 c; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. parameter symbol values unit note or test condition number min. typ. max. data sheet 22 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver electrical characteristics differential voltage ?dominant? high extended bus load normal-operating mode v diff_hext_bl 1.5 ? 5.0 v v txd =0v, r l = 2240 ? , 4.75 v < v cc <5.25v, static behavior; 1) p_9.1.64 driver symmetry ( v sym = v canh + v canl ) v sym 0.9 v cc 1.0 v cc 1.1 v cc v 1) 2) c 1 = 4.7nf p_9.1.67 canl short circuit current i canlsc 40 75 115 ma v canlshort =18v, t data sheet 24 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver electrical characteristics 9.2 diagrams figure 12 test circuit for dynamic characteristics figure 13 timing diagrams for dynamic characteristics figure 14 recessive bit time for five ?dom inant? bits followed by one ?recessive? bit TLE9250X 3 gnd 2 4 5 1 8 100 nf 6 canl 7 canh r l /2 v cc v io txd rm rxd c 2 c rxd 100 nf r l /2 c 1 v diff txd t t rxd 0.9 v t loop(h,l) t d(l),t t d(l),r 0.5 v t loop(l,h) t d(h),t t d(h),r 0.3 x v io 0.3 x v io 0.7 x v io 0.7 x v io t v diff txd t t rxd 0.9 v 5 x t bit 0.5 v t loop(h,l) t t bit t bit(bus) t loop(l,h) t bit(rxd) 0.3 x v io 0.7 x v io 0.7 x v io 0.3 x v io 0.3 x v io v diff = v canh - v canl data sheet 25 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver application information 10 application information 10.1 esd robustness according to iec61000-4-2 tests for esd robustness according to iec61000-4-2 ?gun test? (150 pf, 330 ? ) have been performed. the results and test conditions are available in a separate test report. 10.2 application example figure 15 application circuit table 7 esd robustness according to iec61000-4-2 performed test result unit remarks electrostatic discharge voltage at pin canh and canl versus gnd +11 kv 1) positive pulse 1) not subject to production test. esd susc eptibility ?esd gun? according to gift / ict paper: ?emc evaluation of can transceivers, version iec ts62228?, section 4.3. (din en61000-4-2) tested by external test facility (ibee zwickau, emc test report nr. 01-07-2017 and nr. 06-08-17) electrostatic discharge voltage at pin canh and canl versus gnd -11 kv 1) negative pulse example ecu design v bat TLE9250X v cc canh canl gnd rm txd rxd 7 6 1 4 8 2 3 microcontroller e.g. xc22xx v cc gnd out out in tle4476d gnd iq1 100 nf 100 nf 22 f en q2 v io 22 f 100 nf TLE9250X v cc canh canl gnd rm txd rxd 7 6 1 4 8 2 3 microcontroller e.g. xc22xx v cc gnd out out in tle4476d gnd iq1 100 nf 100 nf 22 f en q2 v io 22 f 100 nf 5 5 optional: common mode choke optional: common mode choke canh canl 120 ohm 120 ohm canh canl data sheet 26 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver application information 10.3 voltage adaption to the microcontroller supply to adapt the digital input and output levels of the tl e9250x to the i/o levels of the microcontroller, connect the power supply pin v io to the microcontroller voltage supply (see figure 15 ). note: in case no dedicated digital supply voltage v io is required in the application, connect the digital supply voltage v io to the transmitter supply v cc . 10.4 further application information ? existing application note of TLE9250X: www.infineon.com/TLE9250X-an ? for further information you may visit: http://www.infineon.com/a utomotive-transceiver data sheet 27 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver package outline 11 package outline figure 16 pg-tson-8 (plastic thin small outline nonleaded) figure 17 pg-dso-8 (pla stic dual small outline) green product (rohs compliant) to meet the world-wide customer requirements for en vironmentally friendly products and to be compliant with government regulations the device is available as a green product. green pr oducts are rohs compliant (i.e. pb-free finish on leads and suitable for pb -free soldering according to ipc/jedec j-std-020). for further info rmation on alternative pa ckages, please visit our website: http://www.infineon.com/packages . dimensions in mm data sheet 28 rev. 1.0 2017-08-09 hs can transceiver high speed can transceiver revision history 12 revision history revision date changes 1.0 2017-08-09 data sheet created trademarks all referenced product or service names and trademarks are the proper ty of their respective owners. edition 2017-08-09 published by infineon technologies ag 81726 munich, germany ? 2017 infineon technologies ag. all rights reserved. do you have a question about any aspect of this document? email: erratum@infineon.com important notice the information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("beschaffenheitsgarantie"). with respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, infineon technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. in addition, any information given in this document is subject to customer's comp liance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of infineon technologies in customer's applications. the data contained in this document is exclusively intended for technically trained staff. it is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. for further information on technology, delivery terms and conditions and prices, please contact the nearest infineon technologies office ( www.infineon.com ). warnings due to technical requirements products may contain dangerous substances. for information on the types in question please contact your nearest infineon technologies office. except as otherwise explicitly approved by infineon technologies in a written document signed by authorized representatives of infineon technologies, infineon technologies? products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury. |
Price & Availability of TLE9250X
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |